Whirlpool Washer LOC Code – Quick Fix Guide (2024)

Did you know that a Whirlpool washer displaying the LOC code can affect the functionality of the appliance, leaving you unable to start a wash cycle? This error, also known as the “LoC” or “LC” code, is a control lock activation feature that prevents accidental changes or operation of the washer’s controls. While it may seem frustrating, resolving this issue is actually quite easy and can save you from unnecessary hassle and worry.

Key Takeaways:

The LOC code on a Whirlpool washer indicates that the control lock is activated.
To activate the control lock, touch and hold the control lock button for 3 seconds.
To deactivate the control lock, repeat the process of holding the control lock button for 3 seconds.
If the control lock persists, try troubleshooting steps such as power reset or control board reset.
In some cases, replacing the touchpad may be necessary. Seek assistance from a professional technician for proper diagnosis and repair.

What is the Control Lock?

The control lock is a feature on Whirlpool washers that allows you to lock the controls to avoid unwanted changes or operation. When the control lock is activated, you will see the code “LoC” or “LC” on the display. This is a reminder that the control lock is set and the controls are locked.

It is important to note that the control lock does not mean that the door is locked. The door will still open, but the washer will not start until the control lock is deactivated.

If you have questions about the control lock on your Whirlpool washer, refer to the owner’s manual for more detailed information and instructions. It will provide you with step-by-step guidance on how to activate, deactivate, and troubleshoot the control lock. Understanding how to use the control lock feature properly can help ensure the smooth operation of your Whirlpool washer and prevent any accidental changes to your settings.

Continue reading to learn how to activate and deactivate the control lock on your Whirlpool washer.

Side note: The image above displays a Whirlpool washer with the control lock activated.

How to Activate the Control Lock

To activate the control lock on your Whirlpool washer and resolve the LOC code issue, follow these simple steps:

Locate the control lock button on your washer.
Press and hold the control lock button for 3 seconds.
While holding the button, observe the display as it counts down from 3 to 1.
Once the countdown is complete, you will see either “LC” or “LoC” on the screen, indicating that the control lock is now activated.
To unlock the control lock, press and hold the same button for an additional 3 seconds.

Note: The control lock button may be a stand-alone key or a dual function key paired with another button. Make sure to press and hold the correct button for three seconds to activate or deactivate the control lock. Avoid pressing the text below the button; focus on the button itself.

By following these steps, you can easily activate and deactivate the control lock on your Whirlpool washer whenever needed.

Quote:

“Activating the control lock is a simple process that can help prevent unintended changes or operation of your Whirlpool washer.” – Whirlpool Customer

Keep in mind:

Refer to your owner’s manual for specific instructions on activating and deactivating the control lock for your model of Whirlpool washer.
Make sure to hold the control lock button for the full 3 seconds to ensure proper activation or deactivation.
If you encounter any issues or the control lock does not respond, try performing a power reset or consult a professional technician.

Pros	Cons
Offers a simple and convenient way to lock the controls to avoid unwanted operation.	May require referring to the owner’s manual for specific instructions based on the model of the washer.
Helps prevent accidental changes or interruptions during a wash cycle.	Requires an additional step to activate or deactivate the control lock.
Provides peace of mind for households with children or pets.	May cause confusion or frustration if inadvertently activated without knowledge of the control lock feature.

How to Deactivate the Control Lock

To deactivate the control lock on your Whirlpool washer, follow these simple steps:

Locate the control lock button on your washer. It is typically labeled with a padlock symbol.
Touch and hold the control lock button for 3 seconds. You may need to refer to your washer’s manual to locate the button if it is not clearly labeled.
As you hold the button, the display will count down from 3 to 1.
Once the countdown is complete, the “LC” or “LoC” code will disappear from the display, indicating that the control lock has been deactivated.

See also Fix Screeching Dryer – Quick Troubleshooting Guide

If pressing the control lock button does not deactivate the control lock, you can try the following troubleshooting steps:

Press the power button to turn off the washer, then touch and hold the control lock button again for 3 seconds.
If the above step does not work, try unplugging the machine or turning off the breaker for 1 minute, then power the machine back on and repeat the deactivation process.

If you continue to experience difficulties deactivating the control lock on your Whirlpool washer, it may indicate a larger issue with the control panel or touchpad. In such cases, it is recommended to consult a professional technician for further assistance.

“Deactivating the control lock on your Whirlpool washer is a straightforward process. By following the steps provided, you can quickly regain control over your appliance’s functions and continue your laundry routine with ease.”

By deactivating the control lock, you can ensure that your Whirlpool washer operates smoothly and efficiently, eliminating any unnecessary interruptions during your laundry cycles.

Troubleshooting the Control Lock

If you are experiencing difficulties with the control lock feature on your Whirlpool washer, there are several troubleshooting steps you can try to resolve the issue. First, ensure that you are following the correct procedure to activate and deactivate the control lock. Consult your owner’s manual for detailed instructions specific to your washer model.

Resetting the Washer to Clear the LOC Code

If the LOC code on your Whirlpool washer does not clear or turn off, you can try resetting the washer to clear the code. There are two methods you can use to achieve this.

Method 1: Power Reset

First, turn off power to the washer by either pulling out the power cord or turning off the breaker that supplies power.
Leave the washer disconnected for up to 5 minutes before reconnecting it.

Method 2: Control Board Reset

“Performing a control board reset can help clear the LOC code from your Whirlpool washer. To perform a control board reset:
Refer to your owner’s manual for instructions specific to your model. The location of the reset button may vary depending on the washer.
Press and hold the reset button for 10-15 seconds. This will reset the control board and clear the LOC code.”

Resetting the washer can often resolve the LOC code issue and allow you to regain control of your Whirlpool washer. Make sure to follow the correct reset procedure for your model and refer to your owner’s manual for detailed instructions.

Replacing the Touchpad

If you have tried deactivating the control lock and resetting your Whirlpool washer, but it still does not respond to your inputs, the touchpad may be faulty. To replace the touchpad, you will need to disconnect the washer from its power source. The process for replacing the touchpad will vary depending on the model of your washer. Generally, it involves the following steps:

Remove the top panel of the washer.
Access the control panel touchpad.
Disconnect any cables or wires connected to the touchpad.
Remove the old touchpad.
Transfer any necessary parts to the new touchpad.
Reassemble the washer.

For specific instructions on how to replace the touchpad on your Whirlpool washer model, it is recommended to refer to your owner’s manual. If you are unsure or uncomfortable with performing the replacement yourself, it is advisable to consult a professional technician who can guide you through the process.

See also Keurig Stopped Working After Descaling? Fix It Now!

Replacing the touchpad can help resolve issues with the control lock and restore the functionality of your Whirlpool washer.

Note: The image above is for visual representation purposes only and may not reflect the exact appearance of your specific Whirlpool washer model.

Replacing the Touchpad on a Dryer

If you own a Whirlpool dryer and it displays the LOC code when the control lock is activated, and you have tried turning it off and resetting it without success, you may need to replace the touchpad.

To replace the touchpad on a Whirlpool dryer, follow these steps:

Disconnect the dryer from its power source.
Remove the top panel and dispenser drawer to access the control panel.
Locate and disconnect any cables or wires connected to the control panel touchpad.
Remove the old touchpad from the control panel.
Transfer any necessary parts from the old touchpad to the new touchpad.
Reassemble the dryer by following the reverse steps of disassembly.

For detailed instructions specific to your dryer model, consult your owner’s manual. If you’re unsure or uncomfortable performing the replacement yourself, it’s best to seek assistance from a professional technician.

Upgrading the touchpad on your dryer will ensure that the control lock functions properly, allowing you to use your appliance without any issues.

Required Tools and Materials

Tools	Materials
Screwdriver Nut driver Pliers	New touchpad

Replacing the Touchpad on a Dishwasher

If you have a Maytag or Whirlpool dishwasher and the control lock indicator light or padlock stays lit even after attempts to turn it off or reset the dishwasher, it may be necessary to replace the touchpad. The touchpad is the interface that allows you to control the dishwasher’s settings and functions.

To replace the touchpad on a dishwasher, you will need to follow these steps:

Disconnect the dishwasher from its power source to ensure your safety.
Remove the outer shell of the dishwasher door. This may involve unscrewing securing screws or clips, depending on the model.
Locate the control panel touchpad, which is usually located on the top front portion of the dishwasher door.
Disconnect any securing screws or wires that are holding the touchpad in place.
Remove the old touchpad carefully, ensuring not to damage any other components.
Transfer any necessary parts from the old touchpad to the new one, such as buttons or sensors.
Securely install the new touchpad in the designated area, making sure it is properly aligned and connected.
Reassemble the outer shell of the dishwasher door, ensuring all screws or clips are tightened.
Finally, reconnect the dishwasher to its power source and test the new touchpad to ensure it is functioning correctly.

It is crucial to follow the instructions in your owner’s manual or seek professional assistance if you are unsure about any step of the touchpad replacement process. This will help ensure proper installation and avoid any damage to your dishwasher.

Remember, if you are experiencing difficulties with the control lock indicator light or padlock staying lit, replacing the touchpad may resolve the issue and allow you to regain full control of your Maytag or Whirlpool dishwasher.

Replacing the Touchpad on a Microwave

If you have a Maytag or Whirlpool microwave and the control lock indicator light or padlock is lit even after attempts to turn it off or reset the microwave, you may need to replace the touchpad. To replace the touchpad on a microwave, you will need to disconnect the microwave from its power source and remove the outer shell of the door. Then, you can locate the control panel touchpad, disconnect any securing screws and wires, remove the old touchpad, transfer any necessary parts to the new touchpad, and finally, reassemble the microwave.

Follow the steps below to replace the touchpad on your microwave:

Disconnect the microwave from its power source.
Remove the outer shell of the door.
Locate the control panel touchpad.
Disconnect any securing screws and wires attached to the touchpad.
Remove the old touchpad.
Transfer any necessary parts from the old touchpad to the new touchpad.
Securely attach the new touchpad to the control panel.
Reassemble the microwave by replacing the outer shell of the door.
Reconnect the microwave to its power source.

For a more comprehensive guide on replacing the touchpad on a microwave, including detailed illustrations and specific instructions based on your model, refer to your owner’s manual or consult a professional technician for proper guidance.

See also Maytag Washer Code 5D: Understanding, Fixing, Preventing

Common Steps to Replace the Touchpad on a Microwave
Steps	Description
1	Disconnect the microwave from its power source.
2	Remove the outer shell of the door.
3	Locate the control panel touchpad.
4	Disconnect any securing screws and wires attached to the touchpad.
5	Remove the old touchpad.
6	Transfer any necessary parts from the old touchpad to the new touchpad.
7	Securely attach the new touchpad to the control panel.
8	Reassemble the microwave by replacing the outer shell of the door.
9	Reconnect the microwave to its power source.

By following the proper steps and guidelines, you can successfully replace the touchpad on your Maytag or Whirlpool microwave and resolve the control lock issue. If you need replacement parts for your microwave, you can visit the Maytag Services – Replacement Parts website for a wide selection of genuine parts.

Conclusion

The LOC code on a Whirlpool washer indicates that the control lock is activated. This can be easily resolved by following the instructions to activate or deactivate the control lock. If the code does not clear or if you experience other issues with the control lock, troubleshooting steps such as power reset or control board reset can be tried. In some cases, replacing the touchpad may be necessary.

It is important to consult the owner’s manual or seek assistance from a professional technician for proper diagnosis and repair. By following these steps, you can quickly fix the whirlpool washer LOC code issue and get your appliance running smoothly again.

FAQ

What does the LOC code on a Whirlpool washer mean?

The LOC code on a Whirlpool washer indicates that the control lock is activated. It is a safety feature that prevents the controls from functioning.

How do I activate the control lock on my Whirlpool washer?

To activate the control lock on your Whirlpool washer, touch and hold the control lock button for 3 seconds. The display will count down from 3 to 1, and you will see “LC” or “LoC” on the screen.

How do I deactivate the control lock on my Whirlpool washer?

To deactivate the control lock on your Whirlpool washer, touch and hold the control lock button for 3 seconds again. The display will count down from 3 to 1, and the “LC” or “LoC” code will disappear.

What can I do if the control lock on my Whirlpool washer is not working?

If the control lock on your Whirlpool washer is not working, make sure you are following the correct procedure to activate and deactivate the control lock. If the issue persists, try pressing the power button to turn off the washer, then unplug the machine or turn off the breaker for 1 minute. Power the machine back on and try activating and deactivating the control lock again.

How can I reset the washer to clear the LOC code?

To reset the washer and clear the LOC code, you can try a power reset by turning off power to the washer for up to 5 minutes. Alternatively, you can perform a control board reset using the reset button on the washer. Refer to your owner’s manual for specific instructions.

What should I do if I need to replace the touchpad on my Whirlpool washer?

If you need to replace the touchpad on your Whirlpool washer, disconnect the washer from its power source and follow the instructions in your owner’s manual or consult a professional technician for guidance on replacing the touchpad.

How do I replace the touchpad on a Whirlpool dryer?

To replace the touchpad on a Whirlpool dryer, disconnect the dryer from its power source and refer to your owner’s manual or seek assistance from a professional technician for proper guidance on removing the old touchpad and installing the new one.

How do I replace the touchpad on a Maytag or Whirlpool dishwasher?

To replace the touchpad on a Maytag or Whirlpool dishwasher, disconnect the dishwasher from its power source and follow the instructions in your owner’s manual or seek professional assistance to ensure proper installation of the new touchpad.

How do I replace the touchpad on a Maytag or Whirlpool microwave?

To replace the touchpad on a Maytag or Whirlpool microwave, disconnect the microwave from its power source and refer to your owner’s manual or consult a professional technician for proper guidance on replacing the touchpad.